Window films are not only popular in the advertising business, but also offer a practical solution for burglary protection and privacy at home. But how do you apply them correctly without creating unsightly bubbles? Here are some tips for easy and successful application:
Preparation is everything Before you apply the window film, clean the surface to be covered thoroughly. Remove all contaminants such as grease, dust or dirt so that the film can adhere optimally.
The right surface Window films stick best to smooth, wipe-proof surfaces. Make sure that the surface is free of unevenness to ensure optimal adhesion.
The right tools For an easy and bubble-free application you need the following tools:
- Universal cleaner or spirit
- Lint-free cloth or nonwoven fabric
- Squeegee or rubber roller
- duct tape
- Commercial hair dryer
- Cutter knife and ruler
The right temperature Make sure that the ambient temperature is between 10°C and 20°C when applying the film. Temperatures that are too high can cause the film to warp, while temperatures that are too low can impair the adhesive strength.
Different bonding methods There are different methods for applying window films. Wet bonding is particularly suitable for beginners, while dry bonding is a faster method for experienced users.
Wet method for applying window films
The wet method is an effective way to apply window films, especially for beginners. Here is a detailed guide on how to do the wet application:
Step 1: Preparation
- Clean the window surface to be covered thoroughly with a universal cleaner or spirit to remove grease, dirt and dust.
- Prepare a soap solution by mixing 1 liter of water with ½ teaspoon of pH-neutral cleaning or dishwashing liquid.
Step 2: Marking and positioning
- Mark the desired position of the film with adhesive tape.
- Spray the soap solution generously onto the window surface to create a slippery surface.
Step 3: Preparing the slide
- Place the window film adhesive side down on a clean, smooth surface.
- Carefully peel off the backing paper of the film, starting at one corner, and spray the adhesive side with the soap solution as well.
Step 4: Applying the film
- Place the film with the adhesive side on the prepared window surface.
- If necessary, move the slide to align it correctly.
- Gently press the film from the center outwards to remove excess water and air bubbles.
- Use a squeegee or soft cloth to make the film smooth and bubble-free.
Step 5: Drying and finishing
- Allow the film to dry for a few hours before further processing.
- Check the film for any bubbles and carefully remove them with a needle.
- Press the film again with a squeegee or rag to ensure it adheres completely.
Dry bonding of window films
Dry application is a faster method of applying window films and is best suited for experienced users. Here is a step-by-step guide:
Step 1: Preparation
- Clean the window surface to be covered thoroughly and remove all dirt.
- Mark the desired position of the film with tape to make it easier to position later.
Step 2: Applying the film
- Place the film adhesive side down on a clean, smooth surface.
- Carefully peel off the backing paper of the film, starting at one corner.
- Position the film between the markings on the window surface and press it firmly.
Step 3: Removing the backing paper
- Continue peeling off the film's backing paper while simultaneously pressing the film smoothly and firmly onto the window surface.
- Work slowly to ensure that the film adheres evenly and without wrinkles.
Step 4: Finishing
- Check the film for any bubbles and carefully remove them with a needle.
- Press the film again with a squeegee or rag to ensure it adheres completely.
- Allow the film to dry for a few hours before further processing.
With these instructions, you can apply window films effortlessly and professionally, regardless of whether you use the wet method or the dry application.
Cleaning and removal After the film is applied, you should clean it carefully with a soft sponge and mild detergent. To remove the film, you can use a hair dryer to heat the adhesive and make the film easier to peel off.
With these tips, you can apply window films effortlessly and without bubbles. Create more security and privacy at home with our high-quality security films!